- Model represented: Willcox and Gibbs improved lockstitch roller puller. Descriptive Notes: Line drawing of Willcox and Gibbs lockstitch roller puller and description of its use; list of Willcox and Gibbs Sewing Machine Company branches. Smithsonian Location: NMAH. Textiles Collection.
- Willcox & Gibbs High Speed Lock-stitch Type 10: Serial No. L 72199 The Willcox & Gibbs High Speed lock-stitch machine was introduced in 1899. It was designed for manufacturing purposes and could produce up to 4,000 stitches per minute in factory conditions. This machine probably dates from the 1950's and was manufactured in America.
- Willcox And Gibbs Superlock Manual
- Willcox And Gibbs Sewing Machine
- Willcox Gibbs Industrial Sewing Machine
- Willcox And Gibbs Manual
If you can get a clearer/better Manual than this Willcox & Gibbs Lockstitch Type 10-A manual than this one (at this price or for less) I will give you a full refund, once I have been shown proof of the better manual. Willcox & Gibbs Lockstitch Type 10-A Sewing Machine Instructions & Parts List Manual (48 Pages including cover) Many Pictures. The Willcox & Gibbs Sewing Machine Company was founded in 1857 by James Edward Allen Gibbs and James willcox gibbs serger manual - manuals online Willcox & Gibbs Type DC-1 Serging Machines Juki Mdl MO-2416N Serger C.R.A. Pacemaker 75 Manual Fabr ic Spreader antique willcox & gibbs manual sewing machine. Like other manufacturers of the Victorian period, Willcox and Gibbs were great believers in putting on a show. Also,like most other companies, the head office had to be in New York.There was no better address than Broadway. Willcox and Gibbs Building, New York City Circa 1903 Library of Congress, Prints & Photographs Division.
THE NEEDLEBAR Online Manuals Section Directions for using the Willcox & Gibbs Automatic Noiseless Sewing Machine
Raise Needle to its highest point, also Presser Foot. Place work under point of Needle. Have two or three inches of thread drawn through the eye of Needle (NOTE -- unless the Needle Bar is at its highest point, the thread is held by the Automatic Tension, and cannot be drawn through).
Pass thread under Presser Foot, towards the left. Let down the Presser Foot, the thread being held fast between the Presser Foot and Cloth.
The thread may be held lightly under the finger, instead of being passed under the Presser Foot, in which case, hold it until two stitchesare made. If held too tightly, the thread will break at the first stitch.
Crossing SeamsThe Automatic Sewing Machine will give no trouble in passing over any ordinary seam. Very heavy seams may need a little assistance.
To Fasten Seam and to Take the Work OutTo Fasten the End of Seam -- Sew off end of seam two stitches: more than this may leave seam unlocked. Stop with Needle at its highest point. With left hand, catch thread between Needle and Thread Pin (6, Fig 9), and pull some slack through the Automatic Tension. With right hand, draw the slack through the eye of Needle, and, grasping thread firmly, cut the thread close to the goods. Lift Presser Foot and then pull the goods from you, and end of thread will be drawn through the loop. Next, pull end of thread, which will tighten the knot and fasten off the seam. If you cannot pull any slack thread from the spool, it is because the Needle Bar is notat its highest point.
To Fasten Seam in the Goods -- Stop the Needle in the goods, place the fingers on the goods close to Presser Foot to prevent goods from moving, raise Presser Foot, and take one more stitch in last hole made. Then break off thread, take out goods and fasten off as directed in preceding paragraph.
To Fasten Seam to be Trimmed or Cut -- Seams that you wish to trim from the finishing end should be fastened by sewing back in the same row of stitching, a little beyond the point of trimming. If it is necessary to trim the finishing end of a seam that has not been fastened as above, immediately after cutting, lock the seam by inserting a pin through loop on under side of goods, pulling end of thread through and drawing it backward upon the seam.
To Take Out Seam -- It is one of the decided advantages of the Automatic Sewing Machine, that, if required, its work can be taken to pieces, without injuring the goods, by simply unlocking the seam at any point, and drawing out the thread. The seam can only be take out in one direction, viz: towards the point of starting. It is therefore a good plan to begin all seams from the end most exposed.
To Turn a Corner -- Stop with Needle raised to its highest point; raise Presser Foot and turn the work. As the thread acts as a pivot the work will become displaced from the position where the Needle was withdrawn; therefore, readjust the work so that the Needle will enter it at proper distance from last stitch. Let Presser Foot down, and proceed.
Difficulties of BeginnersAs in all things 'Practice makes perfect', so in the operation of the Willcox & Gibbs Automatic Sewing Machine, all the varied kinds of work which can be done on it will be accomplished with ease and in perfection as you daily grow more accustomed to its use while closely following this book of instructions. When in trouble arising from inexperience or failure to observe these directions, the following important features should be specially observed:
'It will not feed' -- STITCH REGULATOR not set according to 'Table' on CLOTH PLATE. Thread wound on LOOPER. Needle bent. Threads or ravellings caught on PRESSER FOOT. Cloth caught in HEMMER or other attachment. Very heavy seams will not pass under PRESSER FOOT without a little assistance (See 'Crossing Seams').
'It ravels when I take the work out' -- Stop Machine with Needle at its highest pointand before it runs off the cloth more than two stitches. Never turn Machine backward to raise Needle. This precaution will leave last stitch always locked.
Vdj8proinf_keygen. 'It drops stitches' -- Needle is bent, or not right size for thread according to 'Table'; or you are using soft finished cotton.
'The thread breaks' -- Machine is not threaded up right. You did not start according to instructions. You are sewing goods too hard for Needle to penetrate without soaping, or you are using wrong sized Needle for the thread; black or colored soft finished cotton; or the thread is caught on spool or wound around SPOOL PIN; or Automatic Tension does not hold the thread (See 'Tension does not work' below)
'The Looper winds up' -- Caused either by not holding on to end of thread in starting, or by not putting thread under PRESSER FOOT; or leaving PRESSER FOOT up; or stitch not right by 'Table'. When this difficulty occurs pull down the Cap and clear thread from LOOPER, being careful not to scratch LOOPER.
'It runs hard' -- Machine or Stand needs oiling, or you have been using poor oil that gums. Thread or ravellings are wound in between SMALL WHEEL and CONNECTION ROD -- this can occur only with our earlier AUTOMATIC and B-Machines. All our latest AUTOMATIC Sewing Machines have been so improved that this difficulty is entirely removed.
'Wheel turns backward' -- There is oil on rim of LARGE WHEEL (See directions for preventing Wheel turning backward).
'Belt slips' -- See directions to Tighten the Belt.
'Sewing is much too loose' -- You have a shorter stitch than required by 'Table' or you have threaded through EMBROIDERY SPRING; or you have not drawn thread between the Tension Washers.
NOTE -- Imitation or bent Needles will cause loose stitches and breaking of thread.
'Tension does not work' -- A knot on thread may have broken off in AUTOMATIC TENSION. Raise Needle Bar to highest point, and draw a piece of folded writing paper between Washers, both front and back of Tension.
Accident to MachineIn case of accident, unscrew Machine from Table, pack tightly in a small box, so that it will not be shaken about in transit, and send by Express to us, or any of our Branches for repair. First tie a tag or card with your name and full address to the Machine before sealing up the box, and give the office to which you send it full particulars, stating also number of Machine. Do not send the Thumb Screw or Attachments. Hp dmifit 2.10.
Address: --
WILLCOX & GIBBS S. M. Co., 658 Broadway, New York. Part One -- Part Two
Raise Needle to its highest point, also Presser Foot. Place work under point of Needle. Have two or three inches of thread drawn through the eye of Needle (NOTE -- unless the Needle Bar is at its highest point, the thread is held by the Automatic Tension, and cannot be drawn through).
Pass thread under Presser Foot, towards the left. Let down the Presser Foot, the thread being held fast between the Presser Foot and Cloth.
The thread may be held lightly under the finger, instead of being passed under the Presser Foot, in which case, hold it until two stitchesare made. If held too tightly, the thread will break at the first stitch.
Crossing SeamsThe Automatic Sewing Machine will give no trouble in passing over any ordinary seam. Very heavy seams may need a little assistance.
To Fasten Seam and to Take the Work OutTo Fasten the End of Seam -- Sew off end of seam two stitches: more than this may leave seam unlocked. Stop with Needle at its highest point. With left hand, catch thread between Needle and Thread Pin (6, Fig 9), and pull some slack through the Automatic Tension. With right hand, draw the slack through the eye of Needle, and, grasping thread firmly, cut the thread close to the goods. Lift Presser Foot and then pull the goods from you, and end of thread will be drawn through the loop. Next, pull end of thread, which will tighten the knot and fasten off the seam. If you cannot pull any slack thread from the spool, it is because the Needle Bar is notat its highest point.
To Fasten Seam in the Goods -- Stop the Needle in the goods, place the fingers on the goods close to Presser Foot to prevent goods from moving, raise Presser Foot, and take one more stitch in last hole made. Then break off thread, take out goods and fasten off as directed in preceding paragraph.
To Fasten Seam to be Trimmed or Cut -- Seams that you wish to trim from the finishing end should be fastened by sewing back in the same row of stitching, a little beyond the point of trimming. If it is necessary to trim the finishing end of a seam that has not been fastened as above, immediately after cutting, lock the seam by inserting a pin through loop on under side of goods, pulling end of thread through and drawing it backward upon the seam.
To Take Out Seam -- It is one of the decided advantages of the Automatic Sewing Machine, that, if required, its work can be taken to pieces, without injuring the goods, by simply unlocking the seam at any point, and drawing out the thread. The seam can only be take out in one direction, viz: towards the point of starting. It is therefore a good plan to begin all seams from the end most exposed.
To Turn a Corner -- Stop with Needle raised to its highest point; raise Presser Foot and turn the work. As the thread acts as a pivot the work will become displaced from the position where the Needle was withdrawn; therefore, readjust the work so that the Needle will enter it at proper distance from last stitch. Let Presser Foot down, and proceed.
Difficulties of BeginnersAs in all things 'Practice makes perfect', so in the operation of the Willcox & Gibbs Automatic Sewing Machine, all the varied kinds of work which can be done on it will be accomplished with ease and in perfection as you daily grow more accustomed to its use while closely following this book of instructions. When in trouble arising from inexperience or failure to observe these directions, the following important features should be specially observed:
'It will not feed' -- STITCH REGULATOR not set according to 'Table' on CLOTH PLATE. Thread wound on LOOPER. Needle bent. Threads or ravellings caught on PRESSER FOOT. Cloth caught in HEMMER or other attachment. Very heavy seams will not pass under PRESSER FOOT without a little assistance (See 'Crossing Seams').
'It ravels when I take the work out' -- Stop Machine with Needle at its highest pointand before it runs off the cloth more than two stitches. Never turn Machine backward to raise Needle. This precaution will leave last stitch always locked.
Vdj8proinf_keygen. 'It drops stitches' -- Needle is bent, or not right size for thread according to 'Table'; or you are using soft finished cotton.
'The thread breaks' -- Machine is not threaded up right. You did not start according to instructions. You are sewing goods too hard for Needle to penetrate without soaping, or you are using wrong sized Needle for the thread; black or colored soft finished cotton; or the thread is caught on spool or wound around SPOOL PIN; or Automatic Tension does not hold the thread (See 'Tension does not work' below)
'The Looper winds up' -- Caused either by not holding on to end of thread in starting, or by not putting thread under PRESSER FOOT; or leaving PRESSER FOOT up; or stitch not right by 'Table'. When this difficulty occurs pull down the Cap and clear thread from LOOPER, being careful not to scratch LOOPER.
'It runs hard' -- Machine or Stand needs oiling, or you have been using poor oil that gums. Thread or ravellings are wound in between SMALL WHEEL and CONNECTION ROD -- this can occur only with our earlier AUTOMATIC and B-Machines. All our latest AUTOMATIC Sewing Machines have been so improved that this difficulty is entirely removed.
'Wheel turns backward' -- There is oil on rim of LARGE WHEEL (See directions for preventing Wheel turning backward).
'Belt slips' -- See directions to Tighten the Belt.
'Sewing is much too loose' -- You have a shorter stitch than required by 'Table' or you have threaded through EMBROIDERY SPRING; or you have not drawn thread between the Tension Washers.
NOTE -- Imitation or bent Needles will cause loose stitches and breaking of thread.
'Tension does not work' -- A knot on thread may have broken off in AUTOMATIC TENSION. Raise Needle Bar to highest point, and draw a piece of folded writing paper between Washers, both front and back of Tension.
Accident to MachineIn case of accident, unscrew Machine from Table, pack tightly in a small box, so that it will not be shaken about in transit, and send by Express to us, or any of our Branches for repair. First tie a tag or card with your name and full address to the Machine before sealing up the box, and give the office to which you send it full particulars, stating also number of Machine. Do not send the Thumb Screw or Attachments. Hp dmifit 2.10.
Address: --
WILLCOX & GIBBS S. M. Co., 658 Broadway, New York. Part One -- Part Two Back to Main Index THE NEEDLEBAR Online Manuals Section Directions for using the Willcox & Gibbs Automatic Noiseless Sewing Machine Willcox And Gibbs Superlock Manual (Part One) INSTRUCTIONS RELATIVE TO THE CARE AND OPERATION OF THE PORTABLE ELECTRIC MOTOR To Adjust Motor to MachinePlace machine on motor base, so that the felts on the motor coupling enter the opening in the wheel of the sewing machine; then turn machine-end of motor base towards you, allowing it to project over the edge of the table, and tighten thumb screw underneath. When doing this, be sure that the main shaft of machine is in perfect alignment with main shaft of motor by turning wheel by hand slowly from you. Should it not run freely, loosen thumb screw and adjust machine by slight movement to or from you. Again, turn the wheel and if it runs freely, then tighten thumb screw securely, taking care not to shift machine on base.
To Connect with Lamp SocketScrew plug into electric lamp or base socket; then take plug cap end of flexible cord attached to Foot Controller and snap the two pins into the plug. Do not attempt to screw into or unscrew plug from socket while flexible cord is attached. If you do, you will probably break the wires in the flexible cord.
To Connect Foot ControllerTake the plug cap end of the shorter flexible cord and snap the two pins into the Foot Controller. Light pressure with the foot gives slow speed, more pressure increased speed. The speed may be changed by adjusting the screw underneath the foot pedal, by turning this screw to the right or left. Turning to the right increases speed; turning to the left decreases speed. How much to raise or lower the adjusting screw will be determined by noting speed of machine when foot-piece touches top of screw.
Special CautionBefore applying current, be sure machine wheel turns freely by hand. Esoteric software gloomhaven. If it does not, follow instructions under head 'TO ADJUST MOTOR TO MACHINE'.
1. Do not pull Connections from sockets by grasping the Wire.Take hold of the hard rubber Plug and remove gently. This will prevent disturbing the wires and save you much trouble and annoyance. https://gugunevada971.weebly.com/menstrual-period-tracker-5-9-1.html.
2. To place Electric Automatic and Foot Controller in Carrying Case.Arrange lead wires on sewing machine and foot controller carefully. Turn stitch regulator to 22. Place machine in case at a slight angle so that the base of machine will slip under brackets which hold it in place. Place attachment box back of machine and oil slide in front, after machine is in place. Place foot controller in compartment provided for it at end of case.
3. Never oil Foot Controller.Keep in a dry place.
4. Do not oil Motor.To lubricate motor, remove grease cups and fill them with vaseline.
5. Keep sewing machine thoroughly oiledas per directions on pages 10 & 11 of Instruction Book, using Willcox & Gibbs Automatic Oil.
6. Be sure and use the right Needle and Thread Willcox And Gibbs Sewing Machineby consulting the scale on the right hand side of Cloth Plate. Use only genuine Willcox & Gibbs Sewing Machine Needles.
7. When using Attachments,always consult Instruction Book, using thread needle and stitch as directed. Clc main workbench licence crack.
8. Do not endeavor to make Repairs.Consult the nearest Willcox & Gibbs Office for prompt and courteous service.
DIRECTIONS FOR USING THE WILLCOX & GIBBS NOISELESS AUTOMATIC SEWING MACHINEThe Stand, as shown above, consists essentially of the Table Top; Right Leg; Left Leg; Treadle Rod; Large Wheel, turning upon the Wheel Stud; Pitman, connected at its upper end with crank of Large Wheel by the Crank Stud; and Treadle, connected with the lower end of Pitman by the Treadle Stud.
The Large Wheel is covered in front by a Guard to protect the dress of the operator, and in a recess in this guard is a small Rubber Ball, which acting as a Brake, prevents the Wheel turning the wrong way.
This illustrates the principal parts of the Machine, to which reference is made in the course of these Directions, and a careful study of which will be found exceedingly helpful to the learner.
Treadle PracticeBefore commencing to sew, practice running Machine, with one foot, without thread in the Needle, and with Presser Foot raised from Cloth Plate, until you can with ease produce a regular motion.
The Cap that covers the Looper must be kept closed while practising or sewing.
We advise use of one foot only in running Machine, as it runs so very lightly.
Oiling -- Notes and CautionsA little care bestowed in properly oiling and cleaning Machine will abundantly repay owner in ease of running and general comfort.
Use oil put up expressly by us, which is decidedly best for the purpose, and can be obtained at any of our Branch Offices. Should Machine run hard after standing for some time (which it may do if any oil except ours is used), oil with a little kerosene or benzene, and after running it a few minutes, oil again with our sewing machine oil. (See 'Best Sewing Machine Oil' on page 39)
A bottle of oil and an oiler accompany each Machine sent out by us.
The Machine should be cleaned and oiled two or three times a week, or every day, if in constant use.
Willcox Gibbs Industrial Sewing MachineKeep outer rim of Large Wheel, underneath Table, free from oil. This will prevent its turning backward in consequence of oil reaching Rubber Ball. Should it do so, wipe outer rim of Large Wheel and Rubber Ball thoroughly with a cloth, then apply powdered chalk or pumice stone to Rubber Ball.
If oil gets on your work, rub the spots with soap and cold water before putting the garment in the suds.
Oiling the StandThe Stand requires oiling in only three places, at each of which will be found oil holes, namely Wheel Stud, Crank Stud (both to the right of Pitman), and Treadle at its connection with Pitman (See Fig 1)
To oil them move toe of Treadle to its lowest point. This will raise both Stud oil holes to the top -- the only position in which they can be reached for oiling.
Part Two -- Part Three Willcox And Gibbs Manual Back to Main Index